1500mm Fluted Walnut Double Vanity — Two Basins, One Continuous Front — FAME bathroom cabinet manufacturer
New 2026 · AU 1500mm Double · Fluted Walnut

1500mm Fluted Walnut Double Vanity — Two Basins, One Continuous Front

A 1500 mm wall-hung cabinet with two basins is the format large Australian bathrooms actually ask for, and the reason this one works is the front: the reeding is machined across the whole elevation so the drawer banks and the door panels read as one continuous timber surface instead of four separate boxes. The ribs are 10 mm half-rounds at 20 mm centres cut into a warm walnut veneer, so the light moves down the front as you walk past it, and the 20 mm sintered stone top runs unbroken across both basins with no seam in the middle.

  • 1500 mm (59.1 in) wide wall-hung double-basin unit; 1200 mm and 1800 mm runs off the same carcass programme
  • Fluted walnut veneer fronts — 10 mm half-round ribs at 20 mm centres, run continuously across drawers and doors
  • 20 mm light warm-grey sintered stone top, thin squared edge, no upstand, one unbroken slab across both basins
  • Two white glazed ceramic basins set in flush with thin rims; single tap hole each, three-hole on request
  • 3 mm even shadow gaps, no visible handles — push-open drawers and doors; Blum TANDEMBOX and hinges optional
  • 18 mm moisture-resistant carcass with sealed back panel; wall reinforcement drawing issued with every order

SKU: FAME-WF-1500 · MOQ: 20 pcs · Sample order available

Specifications

Sizes1500 mm (59.1 in) wide standard; 1200 mm and 1800 mm on the same carcass programme; depth 460 mm (18.1 in); carcass height 500 mm (19.7 in)
Carcass18 mm moisture-resistant board with sealed back panel and ABS-sealed edges; E1/E0 board options; full plywood carcass available on request
FrontsFluted walnut veneer on a stable core — 10 mm half-round ribs at 20 mm centres, reeding run continuously across drawer banks and door panels; two long drawer banks plus two door panels
FinishSatin walnut veneer at about 15 percent sheen, grain and rib shadow matched batch to batch; sealed on all faces with PU lacquer for wet-room use
InteriorTwo full-extension deep drawers with dovetail boxes per side, one adjustable shelf behind each door; interior in a pale walnut decor; door-back mirror optional
Countertop20 mm light warm-grey sintered stone, thin squared edge, no upstand; one slab across both basins so there is no centre seam; quartz or solid surface on the same cut-out
BasinsTwo white glazed ceramic basins set in flush with thin rims, overflow drilled; single tap hole per basin pre-drilled, three-hole on request
HardwarePush-open catches and soft-close hinges standard; no visible pulls; Blum TANDEMBOX runners and Blum hinges optional on the same drilling
InstallationWall-hung on a welded steel rail; masonry and 12.5 mm board over timber stud fixings supplied with every order; two-people lift at this width
CertificationsISO9001, CE, SGS, IP44, FSA

Verification & Compliance — Evidence Behind Every Claim

Every FAME unit is built and inspected to the same standards we ship to the world's top-10 bathroom brands. Each claim below carries a verifiable anchor — certificates and inspection reports are available for review on request or during factory audits.

ISO9001 Quality management system CE EU conformity marking SGS Third-party inspected IP44 Splash & moisture resistance per IEC 60529 FSA Forest & safety assurance
IP44 moisture protectionRated to IEC 60529 (splash-proof, protection against objects >1mm). Test method and report available on request.
Soft-close hardwareBlum optional — see Blum official specifications.
Company credentialsFounded 2009 · 20,000 m² factory · supplier to global top-10 bathroom brands. See About FAME and Certifications.
Third-party verificationSGS inspection reports and certificate scans available with your quotation — request them here.

In a Real Bathroom

1500mm Fluted Walnut Double Vanity — Two Basins, One Continuous Front in a real bathroom setting

Every FAME unit is produced in our 20,000 m² factory, inspected against the same standards we ship to the world's top-10 bathroom brands, and container-optimized for your program.

Product FAQ

Is 1500 mm too wide for a wall-hung double basin?
Not if the wall is prepared for it. The load is the stone top plus two basins, so the steel hanging rail has to land on studs or on a plywood pattress rather than on plasterboard plugs, and two fixers should set it. We ship masonry and board-over-stud fixings with every order and issue the reinforcement drawing before first fix, which is the point where this format usually goes wrong on site. If the wall cannot take it, the same carcass programme runs a floor-standing version on adjustable legs.
Why fluted fronts instead of plain walnut veneer?
Because a 1500 mm elevation of flat veneer shows every joint and every change in the grain, and at that width the joints are what the eye finds first. Machining the ribs across the whole front turns four panels into one surface, and the rib shadows hide the 3 mm gaps between fronts. The cost is that the reeding collects dust along each groove, so we seal the ribs with PU lacquer rather than leaving the veneer raw — it wipes out with a cloth instead of needing a brush.
How do you keep the reeding lined up across drawers and doors?
The ribs are cut on one CNC programme and the fronts are indexed from a single datum, so the rib pitch carries from the drawer bank into the door panel below without a step. The fronts for a run are laid out and matched before lacquering, and the reeding is machined after the veneer is pressed but before the finish goes on, which is the only order that holds the alignment. On site the panels only fit one way; the carcass drilling is keyed to the same datum.
Can the two basins be replaced with one long trough basin?
Yes. The stone is cut to a template, so a single sintered trough basin or one long integrated basin is a template change rather than a different cabinet — the carcass and the drawer layout stay as they are. The basin recess depth changes, so the drawer fronts behind it drop by about 40 mm to keep the proportion, and that is quoted from the same programme.
What is the MOQ for this model?
Our MOQ is 20 pieces per model, with sample orders welcome for pre-production evaluation.

Quote This Model for Your Program

Tell us quantity, finish and destination port — we'll come back with pricing, lead time and a sample proposal.

Request a Quote